Directed Electronics 12.2X Automobile Alarm User Manual

User manual for the device Directed Electronics 12.2X Automobile Alarm

Directed Electronics 12.2X Automobile Alarm User Manual

Extracts of contents

Content summary on the page No. 1

Model 12.2X➤Owner’s Guide

Content summary on the page No. 2

limited lifetime consumer warrantyDirected Electronics ("Directed") promises to the original purchaser to repair or replacewith a comparable reconditioned model any Directed unit (hereafter the "unit"), excluding without limitation the siren, the remote transmitters, the associated sensors and accessories, which proves to be defective in workmanship or material under reasonable use during the lifetime of the vehicle provided the following conditions are met: the unit was professionally installed

Content summary on the page No. 3

CONSEQUENTIAL DAMAGES OF ANY KIND. IN THE EVENT OF A CLAIMOR A DISPUTE INVOLVING DIRECTED OR ITS SUBSIDIARY, THE PROPERVENUE SHALL BE SAN DIEGO COUNTY IN THE STATE OF CALIFORNIA.CALIFORNIA STATE LAWS AND APPLICABLE FEDERAL LAWS SHALL APPLYAND GOVERN THE DISPUTE. THE MAXIMUM RECOVERY UNDER ANYCLAIM AGAINST DIRECTED SHALL BE STRICTLY LIMITED TO THEAUTHORIZED DIRECTED DEALER'S PURCHASE PRICE OF THE UNIT.DIRECTED SHALL NOT BE RESPONSIBLE FOR ANY DAMAGES WHATSOEVER, INCLUDING BUT NOT LIMITED TO, ANY

Content summary on the page No. 4

table of contentslimited lifetime consumer warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32-way remote control diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7standard remote configurations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8what is included . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9important i

Content summary on the page No. 5

interpreting zone diagnostics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36owner recognition . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37rapid resume logic . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37power saver mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38programming . . . . . .

Content summary on the page No. 6

2-way remote control diagram23146871-800-274-0200RPN 488V/P/X2(66) CODESFCC ID: EZSDEI487591.Arm/Disarm Indicator (Orange)2.Receive/Transmit Indicator (Green)3.Auxiliary Indicator (Yellow)4.Siren Indicator (Red)5.Arm Button6.Disarm Button7.Panic Button8.Auxiliary Channel Button9.Battery Door© 2006 directed electronics7

Content summary on the page No. 7

standard remote configurationscontrols the Lock–Arm/Panic On/Panic Off function.controls the Unlock–Disarm/Panic Off function.controls Silent Mode™ and an Auxiliary Output (2).controls the Panic On/Off function (hold for 2-seconds).8andpressed together control an Auxiliary Output (3).andpressed together control an Auxiliary Output (4).andpressed together control an Auxiliary Output (5).andpressed together control an Auxiliary Output (6).© 2006 directed electronics

Content summary on the page No. 8

what is included➤One control module➤One four-button LED 2-way transmitter, 488XDOne four-button transmitter, 7141X➤note: On both remotes the panic button is the same color.➤Wire harnesses➤Dual diode harnessThe 514N six-tone programmable siren➤➤➤➤➤➤The in-vehicle status LED indicator lightA push-button Valet switchYour warranty registrationFailsafe® Starter Kill ready circuitry(may require additional labor)548T transceiver/antennaimportant informationCongratulations on the

Content summary on the page No. 9

➜ system maintenanceThis system needs no specific maintenance beyond 2-wayremote control battery replacement. The 2-way remote ispowered by a 1.5V AAA battery. The 1-way remote is poweredby a pair of 3V CR2016 batteries.Low Battery NotificationIf the battery is low (and this feature is programmed On) the 2way remote will emit 2 long beeps 5-seconds after a transmissionis completed. The 2 long beeps will repeat every 25 seconds upto 3 times (or until a 2-way remote button is pressed).Battery Re

Content summary on the page No. 10

➜ fcc/id noticeThis device complies with Part 15 of FCC rules. Operation issubject to the following two conditions: (1) This device may notcause harmful interference, and (2) This device must accept anyinterference received, including interference that may causeundesirable operation.Changes or modifications not expressly approved by the partyresponsible for compliance could void the user's authority tooperate this device.3201 Seriesreplacement remote controlsYou can purchase replacement remote

Content summary on the page No. 11

2-way remote control functionsThe 2-way remote control buttons are used to send commandsto the system. The descriptions below reflect the standard configuration for this system. The buttons can be custom configuredfor the user’s specific needs by the installer.➜ standard configurationButtonThe arming function is controlled by pressing this button forone second.ButtonThe disarming function is controlled by pressing this button forone second.ButtonSilent Mode™ and an optional auxiliary funct

Content summary on the page No. 12

andButtonsAn optional auxiliary convenience or expansion function thatyou have added to your system can be activated by pressing thesebuttons simultaneously.The auxiliary output controls_________________________.andButtonsAn optional auxiliary convenience or expansion function thatyou have added to your system can be activated by pressing thesebuttons simultaneously.The auxiliary output controls_________________________.andButtonsAn optional auxiliary convenience or expansion function thatyou ha

Content summary on the page No. 13

transmitter functionsThis system uses a computer-based learn routine to learn thetransmitter buttons. This makes it possible to assign any transmitter button to any system function. The transmitter initiallycomes programmed with Standard Configuration, but may alsobe customized by an authorized dealer. The buttons in all of theinstructions in this manual correspond to a StandardConfiguration transmitter.14© 2006 directed electronics

Content summary on the page No. 14

remote operationThe system operates at 434 MHz and incorporates Directed’s proprietary out-board technology transceiver. The high frequency combinedwith Binary Data communication achieves superior range with twoway communication.➜ system signal paging featuresA page is the signal the control module sends to the remote controlas confirmation of receipt of a command or alarm system status.When the remote control receives a page it will generate a pagenotification to the user (notifications are

Content summary on the page No. 15

until the alarm page is cleared.If the shock sensor or optional sensor has triggered the alarm theremote will display the alarm page with 6 Red LED flashes and10 rapid beeps.If the trunk, door, ignition, or hood triggered the alarm theremote will display the alarm page with the Red LED illuminating for 3-seconds and 4 rapid beeps (repeated 5 times)Page Recognition (Acknowledgement)To clear a page alert/notification, quickly press any button onthe remote control. This can be performed at any time

Content summary on the page No. 16

programming 2-way remoteTo enter programming modePress and hold all four remote control buttons simultaneouslyuntil one long beep is heard. Programming mode is now entered.Beeps On/OffPressto select beeps On/Off. One beep is notification beepsOn, Two beeps is notification beeps Off. The notification beepsare programmed On from the factory and can be programmedOff if they are not desired. When programmed Off the remotewill only flash the LEDs as notification of a command page oran alarm page.2-Wa

Content summary on the page No. 17

note: If programmed Off, no alarms will be notified to theremote. Command information (Armed/Disarmed) willbe notified to the remote.To exit programming modeThe 2-way LED remote control will exit programming modeafter 2-seconds of inactivity and will emit 2 long beeps.using your systemThe buttons described in this manual correspond to the standardconfiguration. Remember, this is not the only way your transmitter may be set up. It can be custom configured to meet yourneeds. See your installer for

Content summary on the page No. 18

The 2-way remote responds to active arming with one beep andthe Orange LED will flash 3-times to indicate successful armingof the system.If after 2-seconds the remote beeps once and the Orange andRed LEDs flash 3-times, the system has detected an active sensorthat should be checked.If after 2-seconds the remote beeps once, the Orange LED flashes6-times and the Red LED lights for 3-seconds, the system hasdetected an open door, hood or trunk and has been bypassed.➜ passive armingThe system can b

Content summary on the page No. 19

note: If any protected entry point (such as a door or aswitch-protected trunk or hood) is open, the system willnot passively arm (unless forced passive arming is programmed on. See Programming Options section.) Additionally, if a door, hood or trunk is triggered during thearming countdown, the 30-second countdown starts over.When armed your vehicle is protected as follows:➤➤➤➤➤➤20Light impacts trigger the Warn Away® signal. When triggered,the siren chirps and the parking lights flas

Content summary on the page No. 20

➜ multi-level security armingMulti-Level Security Arming allows you to select which of thesecurity system's inputs or sensors will be active and which willbe bypassed at the time that the system is armed. (See the Tableof Zones section of this guide.) Pressingagain within fiveseconds of arming the security system will activate the MultiLevel Security Arming feature. Each timeis pressed again, adifferent security level is selected. The different security levelscan be selected as follows:➤Pres

LEAVE A COMMENT