Ford M-6007-XE3 Automobile Parts User Manual

User manual for the device Ford M-6007-XE3 Automobile Parts

Ford M-6007-XE3 Automobile Parts User Manual

Extracts of contents

Content summary on the page No. 1

M-6007-B50/B51/XE3/XB3EngineINSTRUCTION SHEETNO PART OF THIS DOCUMENT MAY BE REPRODUCED WITHOUT PRIOR AGREEMENT AND WRITTEN PERMISSION OFFORD RACING PERFORMANCE PARTSPlease contact the Tech “Hot Line” for the most current instruction information (586) 468-1356! ! ! PLEASE READ THE FOLLOWING INSTRUCTIONS CAREFULLY PRIOR TO INSTALLATION ! ! !GENERAL INFORMATION:This engine assembly is built with current production 5.0L H.O. crankshaft, rods and pistons, resulting in a 50 oz. externalbalance re

Content summary on the page No. 2

M-6007-B50/B51/XE3/XB3EngineINSTRUCTION SHEETNO PART OF THIS DOCUMENT MAY BE REPRODUCED WITHOUT PRIOR AGREEMENT AND WRITTEN PERMISSION OFFORD RACING PERFORMANCE PARTSPARTS REQUIRED TO COMPLETE THE ENGINE:Water Pump and Plate:The front cover and water pump supplied are for a reverse rotation serpentine style system. Some serpentinesystems may also require a different timing chain cover and water pump. A V-belt system may require a differentfront cover to use your standard rotation water pump.Dist

Content summary on the page No. 3

M-6007-B50/B51/XE3/XB3EngineINSTRUCTION SHEETNO PART OF THIS DOCUMENT MAY BE REPRODUCED WITHOUT PRIOR AGREEMENT AND WRITTEN PERMISSION OFFORD RACING PERFORMANCE PARTSAPPLICATION INFORMATION:Depending on the date of manufacture, this engine may be equipped with either 1995 Mustang or 1996 Explorer dresscomponents (except Explorer dressed engines will be built with F-Series M/T flywheels). These components include frontcover, water pump, oil pan, pick-up tube and screen assembly, and flywheel. A l

Content summary on the page No. 4

M-6007-B50/B51/XE3/XB3EngineINSTRUCTION SHEETNO PART OF THIS DOCUMENT MAY BE REPRODUCED WITHOUT PRIOR AGREEMENT AND WRITTEN PERMISSION OFFORD RACING PERFORMANCE PARTSPRIMING THE ENGINE LUBRICATION SYSTEM:! ! ! WARNING: DO NOT ATTEMPT TO START ENGINE WITHOUT FILLING THE CRANKCASE WITH OIL ANDPRIMING THE LUBRICATION SYSTEM ! ! !NOTE: Prime the engine oiling system before the engine is installed into the vehicle.STEP 1:Fill the crankcase with (5) five quarts of 10W-30, 10W-40 premium motor oil.STEP

Content summary on the page No. 5

M-6007-B50/B51/XE3/XB3EngineINSTRUCTION SHEETNO PART OF THIS DOCUMENT MAY BE REPRODUCED WITHOUT PRIOR AGREEMENT AND WRITTEN PERMISSION OFFORD RACING PERFORMANCE PARTSSTEP 4:Verify rotor blade is pointing at #1 mark on the distributor base.NOTE: If the rotor blade & the magnetic pick-up cannot be aligned by rotating the distributorin the engine block, remove the distributor enough to disengage the distributor drive gear fromthe camshaft gear. Rotate the rotor enough to engage the distributor gear

Content summary on the page No. 6

M-6007-B50/B51/XE3/XB3EngineINSTRUCTION SHEETNO PART OF THIS DOCUMENT MAY BE REPRODUCED WITHOUT PRIOR AGREEMENT AND WRITTEN PERMISSION OFFORD RACING PERFORMANCE PARTS5.0L SPECIFICATIONS:Bore:Stroke:Displacement:Nominal Compression Ratio:Block Height:Piston to Deck:Camshaft: (Hydraulic Roller)4.03.0302 CID9.0:18.206.0075 below to .0135 aboveM-6250-B303Maximum Valve Lift .480Duration at .050 lift 224Intake Centerline 107Lifters:Current productionValves:Valve Springs:Rocker Arms:M-6007-B50/B51/XB3/

LEAVE A COMMENT