Audiovox AA-RS10CS Remote Starter User Manual

User manual for the device Audiovox AA-RS10CS Remote Starter

Audiovox AA-RS10CS Remote Starter User Manual

Extracts of contents

Content summary on the page No. 1

Model AA-RS10CSInstallation Manual3 Channel Remote Start / Keyless Entry SystemInstallation InstructionsThis Unit is Intended for Installation in Vehicles with 12 Volt Negative GroundElectrical Systems, Gasoline or Diesel with True Tach Reference and AutomaticTransmissions Only.Kit ContentsAA-RS10CS Control Module(2) - 3 Button Anti Code Grabbing Transmitters3 Channel Code Learning ReceiverExternal Superheterodyne Antenna/Receiver(1) - Multi Pin Input/Output Harness(1) - Six Pin Power Harness(1)

Content summary on the page No. 2

The AA-RS10CS Remote Start/Keyless Entry System is designed to be used with Automatic Transmission Vehicles Only!The unit provides a selectable ignition control that allows a 10 second output for glow plug pre-heat which may be requiredfor certain diesel vehicles, (see selectable feature #9). If the diesel engine has a instant fire, (no glow plug pre-heatsystem), feature #9 should remain in the default Gasoline mode setting. For diesel applications, consult your dealer forthe type of ignition sy

Content summary on the page No. 3

WIRING THE 6 PIN MAIN POWER HARNESS:RED w/ WHITE Trace Wire: + 12 volt Battery 1 SourceConnect this wire to a + 12 VDC constant source found at the vehicle's ignition switch using the 30 Amp fuse andholder provided. This wire provides power for the control circuit as well as the ignition 1 and ignition 2 relays.RED Wire: + 12 Volt Battery 2 SourceConnect this wire to a + 12 VDC constant source found at the vehicle's ignition switch using the 30 Amp fuse andholder provided, but NOT the same vehic

Content summary on the page No. 4

BLUE Wire: Ignition 1 OutputConnect this wire to the ignition 1 wire from the ignition switch. This wire will show +12 volts when the ignition key isturned to the to the "ON" or "RUN" and the "START" or CRANK" positions, and will have 0 volts when the key is turnedto the "OFF" and "ACCESSORY" positions.For Diesel Applications, this wire must be connected to the ignition circuit that powers the glow plugs if the vehiclerequires glow plug pre-heating. (See selectable feature #9)GREEN Wire: Ignitio

Content summary on the page No. 5

GREY Wire: Negative Inhibit Input 1Connect the GREY wire to the previously mounted hood pin switch provided . This wire will be routed through the fire wallinto the engine compartment. It is necessary to use an existing grommet when passing wires through the fire wall to preventshort circuiting. This is an important safety feature of APS 675, and failure to use this feature can result in serious injury.Route the wire to the pin switch and connect it using the bullet connector provided.GREY w/ BL

Content summary on the page No. 6

(2) WHITE Wires: Parking Light FlasherThese wires are the COMMON and NORMALLY OPEN contacts of the on-board parking lamp relay.If the vehicle's parking lights are a +12 volt switched system, connect (1) of the White wires to a fused (15A max.) +12volt battery source, and connect the second White wire to the vehicle's parking light wire.If the vehicle's parking lights are a chassis ground switched system, connect (1) of the White wires to a chassis groundsource, and connect the second White wire

Content summary on the page No. 7

4. Cut (#1) wire (as shown), and connect the ignition switch side of the cut wire to terminal #87a of the relay.Connect the other side of the (#1) wire to terminal #30.5. Connect the previously selected resistor from terminal #87 to the second (#2) wire (as shown).NOTE: The above information and following diagram is for the GM VATS system only. For GM PASS LOCK Systemyou will require the Audiovox AS-PASS II Module.General Motors VATS By-Pass DiagramDARK GREEN Wire: Tach Sensor InputThis wire wil

Content summary on the page No. 8

In this application, the Red wire of the two pin harness provides a ground pulse during the arming sequence, or pulsedground lock output. Connect the Red wire to the low current ground signal wire from the factory door lock switch to thefactory door lock relay.The Green wire of the two pin harness provides a ground pulse during the disarming sequence, or pulsed ground unlockoutput. Connect the Green wire to the low current ground signal wire from the factory door unlock switch to the factorydoor

Content summary on the page No. 9

Audiovox AS-9159 Door Lock Interface, (or equivalent 30 A automotive relays) must be used. Refer to the AudiovoxDoor Lock Wiring Supplement for proper wiring of these circuits.4 Wire Polarity Reversal and5 Wire Alternating 12 VoltDoor Lock Control CircuitsIn these applications, the AS 9159 Door Lock Interface ( or equivalent 30 A automotive relays) must be used. Refer tothe AUDIOVOX Door Lock Wiring Supplement for proper connection to these types of circuits.2 Pin Blue Connector : Programming Sw

Content summary on the page No. 10

Feature Selection1 Flash2 FlashesDefaultFirst1 Second Door Locks3.5 Second Door Locks1 SecondSecond10 Minute Run Time15 Minute Run Time10 MinuteThirdPark Lights Steady OnPark Lights FlashSteadyFourth(No Function)Tach OperationTachFifth(No Function)(No Function)------------SixthIgn. 2 Off During CrankIgn. 2 On During CrankOff During CrankSeventhDiagnostics OffDiagnostics OnOffEighth(No Function)(No Function)-------------NinthGasoline EngineDiesel EngineGasolineTenthStarter Pole 5XStarter Pole 3XP

Content summary on the page No. 11

and or single injector. To learn tach;1. Start with the programming switch in the OFF position.2. Turn the ignition key to the ON position.3. Flip the program switch ON - OFF - ON - OFF - ON - then OFF.4. Immediately turn the ignition key OFF.5. Flip the program switch ON, then start the vehicle using the ignition key.6. When the unit senses the tach signal, the parking lights will begin to flash.7. Flip the program switch OFF. The parking lights will turn on for 3 seconds to indicate that the t

Content summary on the page No. 12

2. For vehicles utilizing 2 cylinder firing per coil pack, connect Green/Black to the tach side of each coil pack. For 8cylinder, four coil systems, connect to any of the three coils.3. Connect the Yellow wire to a +12 volt ignition 1 source. This wire will have +12 volts with the ignition in the on andstart position and have 0 volts with the ignition in the off position.4. Connect the Green wire to the (Green) or (Orange/Green) tach input of the Audiovox remote start unit.TESTING YOUR INSTALLAT

Content summary on the page No. 13

4. Sitting in the vehicle, start the engine using the vehicle's ignition key.5. Step on the brake pedal and shift the gear selector into reverse.6. Allow the transmission to shift. When you feel the engine pull, do not move the gear selector just turn the ignitionswitch off. DO NOT attempt to remove the key.7. Keeping the brake pedal depressed, activate the RF transmitter in an attempt to start the vehicle. The car should notstart.8. Repeat the above test this time move the gear selector to the

Content summary on the page No. 14

KEY IN SENSOR CIRCUITS:If the vehicle you are working on does not have or you cannot locate the ECM reference wire, there are two alternativesavailable. Although not preferred, the vehicle Key In Sensor may be re-configured to allow a margin of safety and willprevent the vehicle with a Mechanical Neutral Start Switch from starting in gear.AUDIOVOX ADVISES THAT YOU MAINTAIN THE FACTORY CIRCUIT WHENEVER POSSIBLE. The following twocircuits may be used only if the above circuit is not available.NOTE

Content summary on the page No. 15

Remote Start Unit as shown below.METHOD 2To connect to the key in sensor circuit as shown for method 2:A. Locate the control wire that connects the drivers door pin switch to the key in sensor switch.B. Cut this wire and connect the ignition cylinder side to chassis ground.C. Locate the key in sensor switch wire that connects the chime module to the ignition cylinder .D. Cut this wire and connect the ignition cylinder side to the Remote Start Negative Safety Shut down Wire Gray/Black,using a 400

Content summary on the page No. 16

WIRING DIAGRAM© 2000 Audiovox Electronics Corp., Hauppauge, NY 11788128-5850

LEAVE A COMMENT